Home » Handyman

Category Archives: Handyman

Tools For the Handyman

Handymen are hired to address various home improvement tasks that do not require the specialized expertise of licensed professionals. They typically work in residential and commercial settings.


Many handymen start their careers as apprentices to more experienced workers, then take on freelance projects and build a reputation for themselves. Some also take courses in their areas of expertise, like plumbing and electrical repairs. Visit Website to learn more.

Whether you are an electrician or just an experienced handyman, the fish tape is one of the most important tools in your toolbox. It can help you run wires in a wall and get them to the right place without damaging the surrounding structure. It can also help you make minor repairs to existing wiring.

A fish tape is usually made of stainless steel and has a high tensile strength that can handle pushing and pulling forces. It is available in various lengths, and it is a good idea to get one that is long enough for the job you are working on. In addition, it should be corrosion-resistant and can withstand heat. Some fish tapes have a built-in insulating core, which helps protect the conductors from exposure to moisture.

This handy tool is especially useful for routing wires in walls and occupied conduits. It has hooks on both ends that can be attached to existing electrical cables. Once you’ve hooked up the tape, slowly pull it back and feed it into the wall or conduit. It can take some time, but you’ll eventually get it to the desired location.

Before using the fish tape, make sure to turn off any electricity in the area where you’re working. It’s also a good idea to have some extra wire or cable on hand in case your fish tape gets hung up and stops working.

When you’re ready to use the fish tape, remove it from its plastic reel and coiled form. It should have support ties around it that hold it in a coiled shape. These ties should stay in place until the tape is safely inside the wall.

Electrical tape

Electrical tape is a type of pressure-sensitive tape used to insulate wires and other materials that conduct electricity. It can be made from a variety of materials, including vinyl, rubber, and cloth, and is available in a wide range of widths and lengths. It is typically used to protect against electric shock and prevent short circuits, but can also be used to secure loose wiring or provide a moisture barrier.

Unlike regular tape, electrical tape has high levels of electrical resistance. This is because it is designed to protect against electrical currents, so it can withstand higher voltages and currents. It is also highly durable and can withstand abrasions, which makes it ideal for use in rugged environments.

When using electrical tape, be sure to read the label carefully before applying it to a project. Different types of electrical tape have varying properties, so it is important to choose the right one for your project. For example, if you are binding wires, be sure to turn off the power at the circuit breaker before beginning work. It is also important to test for current with a voltage tester before starting the project.

While it is possible to use other types of adhesive tape for electrical applications, they are not recommended because they do not offer the same level of resistance as electrical tape. In addition, regular adhesive tapes do not withstand heat and may fall off. Therefore, it is essential to purchase a quality electrical tape that carries the Underwriters Laboratories (UL) approval. This step ensures that the product has been tested based on national safety standards. If you are unable to find an electrical tape that meets your needs, there are several alternatives available, including heat shrink tubing and wire connectors.

Chalk line

Chalk lines are simple tools that help handymen work faster and more accurately. They’re usually found in most hardware stores and can be used to create straight lines on surfaces such as plywood or drywall. They’re also useful for marking the positions of nails, screws or tacks. Using the chalk line correctly will help you get perfectly straight marks on your project.

The basic chalk line consists of a case with a string and a bottle of powdered chalk. It’s easy to use and affordable, but it can be hard to find a good one. To get the best results, use a chalk line with a good gear ratio and a fine thread. This will ensure that all the string contacts the chalk and gives clean snap lines. It’s also important to buy the right color. Red chalk lines contrast well with metal and plastic, while yellow is a good choice for wood surfaces. It’s also a good idea to get a line with a metal clip for the end of the string.

To use the chalk line, first locate the rewind crank on the case. Then, stretch the string tight and position it against a surface. You can use the case itself as a plumb bob by suspending it from its hook ring. Once the string is in place, pull it toward the other mark and snap it to transfer the chalk.

Using the chalk line requires some practice, but it can be very helpful in many projects. It can save a lot of time and effort by allowing you to draw accurate, straight lines in seconds. Whether you’re hanging a picture or fixing a door, the chalk line will make your job much easier.

Claw hammer

A claw hammer is a must-have tool for any handyman. It can help you hang artwork, pictures and other items on the wall, assemble furniture and much more. You can find these hammers at hardware stores and even online. They are available in a variety of sizes, from 7-32 oz (200-910 g). A high quality claw hammer can last a lifetime if it is used properly.

Claw hammers are double-sided tools that have a nail-driving hammer face and a curved claw. The curved claw side of the head provides leverage to remove nails from surfaces without damaging them. It is also great for pulling out nails that have been driven into the wrong place. To use a claw hammer, simply position it underneath the nail head and pull the handle towards you. You can also try using a wood block under the hammer’s poll to provide some leverage.

Typically, a claw hammer is lighter than a framing hammer, weighing about 20 to 24 ounces. Its face may be smooth or serrated, and the handle is usually made of metal, fiberglass or wood. Some models have a long neck to allow for better pounding accuracy. A claw hammer is a very versatile tool, but it’s not the best choice for demolition work, as you would need to use a more powerful tool, like a sledgehammer.

Another tool that can be a handyman’s friend is the drywall hammer. These hammers are designed to drive nails into drywall without damaging the surface of the board or the surrounding material. They are lightweight and easy to handle, making them a good choice for demolition work. Some models have a rubber grip on their handles, which helps to reduce impact shocks and vibrations. This can reduce hand fatigue and prevent damage to the hands, muscles and nerves.

Circular saw

A circular saw is a handy tool to have, and you can use it for a number of different projects. However, before you can use the circular saw, it is important to understand how it works. It is also a good idea to take a look at the unit’s owner manual and follow all safety recommendations. You should also know how to properly mount a blade into your unit. Then, you can adjust the depth and angle of the blade by loosening and adjusting them respectively (locations of these knobs vary by unit).

If you’re planning to make a rip cut with your circular saw, it’s a good idea to clamp your material in place to keep it steady while you work. This will minimize the tear-out on the back side of your wood and help you get a clean, straight cut. In addition, if you’re making a crosscut, be sure to secure the material against a workbench or sawhorse. Otherwise, the workpiece could shift and cause a dangerous kickback.

Many people believe that a circular saw can be used to cut curves, but it is generally better to use a jigsaw for this task. Nevertheless, if you must use the circular saw to make a curved cut, start by marking the intended curve line with a pencil or chalk line. You can then clamp a piece of scrap wood or pick up a purpose-made guide attachment for your particular saw model. It is also important to block the wheel of the circular saw with a screw or the cut-off wheel locking button that some units come with. This will prevent accidental cuts from the movable wheel.